- File photo

File photo

School bus fleet electrification is getting a lot of attention, and rightfully so. The way school buses are used — for short periods of time with gaps in activity that are perfect for charging — makes them a prime market for electrification.

After the initial up-front investment in electric capabilities, there is less cost around maintenance and fuel, and the vehicles are quieter and more environmentally friendly. As School Bus Fleet has noted, there are maintenance similarities and differences between electric buses and combustion-engine buses. While some components under the hood, such as hoses and coolant, are the same, differences include the need to disable batteries during repairs, a noise generator, and significantly fewer parts in an electric motor.

Moreover, differences apply not just to how the bus is propelled but also to heating, ventilation, and air conditioning.

So, how exactly should fleet operators go about navigating these changes? Here are four recommended steps.

1. Select the Right Compressor.

First, figure out whether a single or dual compressor — or multiple compressors — is most appropriate for your situation. A lot of school buses today are set up with dual compressors — one for the driver and dash area (for defrosting and defogging) and another for cooling the passenger compartment — unlike single-compressor systems that are more appropriate for driver-only vehicles. The number of passengers is a key difference that makes school buses more complex than heavy-duty trucking, off-road, and other markets.

One advantage of the dual- or multiple-compressor solution is the avoidance of long lines from the under-hood compartment to a rooftop unit. The compressor can be co-located with its HVAC components. This will prevent oil traps that are typically seen on belt-driven long line configurations.

Another consideration is battery and electric powertrain cooling. Due to the different evaporating temperatures needed for the battery versus the cabin, it is sometimes favorable to use separate refrigerant loops to cool them.

The first step operators must take when looking at heating and cooling in an electric bus is determining whether a single or dual compressor — or multiple compressors — is most appropriate for a fleet. - Photo courtesy T/CCI Manufacturing

The first step operators must take when looking at heating and cooling in an electric bus is determining whether a single or dual compressor — or multiple compressors — is most appropriate for a fleet.

Photo courtesy T/CCI Manufacturing

2. Determine Heating Method.

How will the bus be heated? Will a heat pump be used to extend driving range? This is an important distinction as it informs the compressor selection and system design. Without an internal combustion engine or fuel-fired heater, an electric bus must use electricity to create heat. Heat pumps utilize the refrigerant system to provide heat in cold weather, using less energy than resistive heaters, resulting in more driving range.

Due to the high expense of batteries, heat pumps are becoming a popular technology for electric vehicles. The concept of the heat pump is simply a reversal of the cycle in which heat energy is absorbed at the condenser from the ambient and then rejected at the evaporator to provide interior heating. It is based on the same exact principle of moving energy from the evaporator to the condenser during air-conditioning operation. It takes a robustly designed electric scroll compressor to operate at these unique conditions, as oil return is low due to the loss of refrigerant mass flow at lower operating conditions.

Additionally, since you are operating at higher-pressure ratios, having a more robust scroll coating to protect in these extreme conditions is critical. Further, there is a point climatically in which the heat pump cannot efficiently transfer enough energy from very cold ambient to meet heating demand. This is where auxiliary resistance heat becomes necessary to continue to provide a boost and achieve full comfort in the bus.

3. Know the Battery Pack Voltage.

What voltage is your battery pack? The electric compressor must be able to operate across the battery operating range. As a rule, the voltage should be lower for hybrids and higher for full-electric vehicles. Batteries with maximum voltages between 400V and 850V are typically used on school buses, heavy-duty trucks, transport refrigeration vehicles, and automotive applications. The higher the voltage, the faster large battery packs can be charged. This allows buses to go back to the bus facilities after morning runs and be ready to go by the afternoon.

Richard Demirjian is president of T/CCI Manufacturing, a supplier of compressor technology to the trucking, off-highway, specialty vehicle, and transport refrigeration markets. - Photo courtesy T/CCI Manufacturing

Richard Demirjian is president of T/CCI Manufacturing, a supplier of compressor technology to the trucking, off-highway, specialty vehicle, and transport refrigeration markets.

Photo courtesy T/CCI Manufacturing

4. Choose Communication Protocol.

Which communication protocol should be chosen for the bus? When considering compressors for electrification, it is important to understand the differences between vehicle communication networks: Controller Area Network (CAN) and Local Interconnect Network (LIN). LIN networks use a centralized design that has each module talking to the main controller. CAN networks have all modules able to communicate with each other. Due to its higher data speeds, CAN networking is often used for the most critical and complex modules, some of which have communication to the outside world. Because of this, CAN networks are more susceptible to hacking and have important cybersecurity considerations, which is a disadvantage.

The shift to electrification is already taking place in the school bus market. India and other parts of Asia will be areas to watch as they are leading the transition in terms of school buses and public transit buses. Now is the time to educate and prepare.

Richard Demirjian is the president of T/CCI Manufacturing, a supplier of compressor technology to the trucking, off-highway, specialty vehicle, and transport refrigeration markets with a global footprint that includes manufacturing operations in China, Argentina, India, and the U.S.

Originally posted on School Bus Fleet

0 Comments